Glass Tile Necklaces

 

I purchased all my supplies on e-bay from an ebay store run by "those_sweet_sensations" They had the best deals I could find and provided the directions for free :)
These are the directions provided, with notes from me in italics... along with the pics of my first try.

Simple Instructions for Pendant Making


Remember, if you're working with images printed on an inkjet printer you'll want to use MicroGlaze to prevent the images from running. Apply a thin coat of MicroGlaze over your image and let it dry for about 10 minutes. Then proceed with the instructions below. (I didn't do this and it turned out fine)

Here’s what you’ll need:

Glass Pieces (the actual pendant)
Diamond Glaze (holds the image on the glass and makes the image crystal clear)
E-6000 (holds the bail or magnet on back of the glass)
Decorative Paper or your own images (use chiyogami paper or your own)
Bail (used for the chain or necklace)
Scissors
Grab a nail file, it will be handy! (optional- I didn't need it)
Pencil (this is to trace your tile- I precut paper pieces)


You’ll be working with glue so be sure to work on a paper towel or such so that you don’t make a mess. :o)

This is going to be much easier than you ever imagined and so much fun!!!

1) First, lay a glass piece down on your work surface with the flat textured side up.

2) Select a piece of decorative paper or printed image to use.

3) Place the paper over the glass so that the undecorated (textured) side is facing up.

4) Now, pick up the glass and the paper and hold them up to a light so that you can see the glass through the paper. You should be able to see the designs on the paper, adjust the paper so that the design on the paper is where you want it to be.

***If using my paper punch skip the next 2 steps***
***You can easily see the image and position through the bottom of the punch***

5) Use a pencil and carefully trace the shape of the glass.

6) Now use your scissors to cut out the pattern that you drew, cut to the outside of your line, you’ll want your cut out to be slightly larger.

7) Now, open your Diamond Glaze. If this is the first time that you’ve used it you’ll need to cut off the tip (just the tip, no more than a few millimeters).

8) Turn your Diamond Glaze container upside down so that the nozzle is down over the glass. Don’t squirt any out just yet, give the air inside the container time to rise – this will decrease the chance of you getting bubbles. You’re not going to be applying a thick coat of glaze in this step, just a thin layer.

9) Next, slowly squeeze the container so that the Glaze starts coming out. Try to keep from getting bubbles. If you do get bubbles just use the tip of the Diamond Glaze container to pop them, or, drag them around until they pop.

10) Apply a thin even layer. In this step I usually apply a little glaze and then use the tip of the container to spread it around evenly, applying more glaze as necessary.

11) Now, go ahead and place your paper onto the glass so that the decorated side is down (in the glaze). Gently adjust the paper so that it’s centered. Don’t press down on the paper with your finger, as this will make a mess. If the paper that you cut is too big, don’t worry, that’s what the nail file will be used for. Let this set for about 30 min. (for MOPS I tested the whole process with only a few minutes between each step and was just fine)

12) Once dry, use the nail file and gently scrape off the excess paper around the edges so that it fits your glass. (I trimmed with scissors)

13) Go ahead and apply more glaze over the back side of the paper and seal the paper to the glass. Be careful when you get to the edges and try not to let the glaze run over the edge, but do try to get your glaze all the way over the edge of the paper so that it seals the paper completely. Once you have a nice layer over the back of the paper let it dry for about 30 minutes. (once again- I just had a couple of minutes)

14) Now you can add your bail or magnet, you can use E6000 as the adhesive for attaching bail. Just put a bit of E6000 down and then place your bail down where you want it.

Allow this to dry over night and that’s it!!!

Like I said, this is so easy,
Most importantly...remember to have FUN!!!